會員1.png)
? IS220PPDAH1A 配電系統反饋單元
| 電路板描述 | 配電反饋系統包 |
| 直接保護措施 | 沒有人 |
| 功能縮寫/縮寫 | PPDA |
| LED數量 | 八 |
| 位置 | 配電模塊 |
| 指南 | GEH-6721L |
| 模擬輸入的數量 | 五 |
/u003Cp dir=/u0022ltr/u0022/u003EAnother key feature of the IS220PPDAH1A board is that it allows for corrective action to occur by sending and reporting information but it cannot take directive protection action. This board supports system maintenance by sending timely information to the PDM. /u003Cstrong/u003EThe PPDA board can receive feedback from up to six PDM components, most of these components are JPDx boards and will host the PPDA I/O pack./u0026nbsp;/u003C/strong/u003E/u003C/p/u003E
/u003Cp dir=/u0022ltr/u0022/u003EThe IS220PPDAH1A board uses electronic IDs to determine power distribution information, the information will then be used to populate the IONet outputs and provide the correct information and feedback to the conjoining boards./u0026nbsp;/u003C/p/u003E
/u003Cp dir=/u0022ltr/u0022/u003EPlease note that when the IS220PPDAH1A board is used in applications reading two hundred forty volts of alternating current it should not cross-connect with the volts of direct current; when this occurs the peak voltage will exceed the MOV rating and cause a failure./u003Cstrong/u003E Failures occur as most of the alternating current supplies must operate on a grounded neutral./u0026nbsp;/u003C/strong/u003E/u003C/p/u003E"}">
產品說明
配電反饋板IS220PPDAH1A是通用電氣公司生產的Mark VIe系列的一部分。該板是配電模塊的一部分，在這種配置下，它將為接地故障檢測、大容量電源健康、電源總線電壓和分支電路狀態提供反饋。該模型能夠具有完整的系統反饋和監控，這使其不同于標準的配電方法。請注意，盡管該模型為分支電路提供反饋，但分支電路并不直接連接到PPDA組件。
IS220PPDAH1A板的另一個關鍵特性是，它允許通過發送和報告信息來采取糾正措施，但不能采取直接保護措施。該板通過向PDM及時發送信息來支持系統維護。PPDA板可以接收多達六個PDM組件的反饋，這些組件中的大多數是JPDx板，并將托管PPDA I/O包。
IS220PPDAH1A板使用電子id來確定配電信息，該信息將用于填充IONet輸出，并向連接板提供正確的信息和反饋。
請注意，當IS220PPDAH1A板用于讀取240伏交流電的應用中時，它不應與直流電壓交叉連接；當這種情況發生時，峰值電壓將超過MOV額定值并導致故障。由于大多數交流電源必須在中性點接地的情況下工作，所以會出現故障。
